24/7 Emergency Services Available

Call Today: (800) 323-7478
24/7 EMERGENCY
Get an Estimate Schedule Service

Geothermal Heat Pumps

Types of Geothermal Heat Pumps

There are four basic types of ground loop systems. Three of these — horizontal, vertical, and pond/lake — are closed-loop systems. The fourth type of system is the open-loop option. Which one of these is best depends on the climate, soil conditions, available land, and local installation costs at the site. All of these approaches can be used for residential and commercial building applications.

CLOSED-LOOP SYSTEMS

Most closed-loop geothermal heat pumps circulate an antifreeze solution through a closed loop — usually made of plastic tubing — that is buried in the ground or submerged in water. A heat exchanger transfers heat between the refrigerant in the heat pump and the antifreeze solution in the closed loop. The loop can be in a horizontal, vertical, or pond/lake configuration.

One variant of this approach, called direct exchange, does not use a heat exchanger and instead pumps the refrigerant through copper tubing that is buried in the ground in a horizontal or vertical configuration. Direct exchange systems require a larger compressor and work best in moist soils (sometimes requiring additional irrigation to keep the soil moist), but you should avoid installing in soils corrosive to the copper tubing. Because these systems circulate refrigerant through the ground, local environmental regulations may prohibit their use in some locations.

HORIZONTAL

This type of installation is generally most cost-effective for residential installations, particularly for new construction where sufficient land is available. It requires trenches at least four feet deep. The most common layouts either use two pipes, one buried at six feet, and the other at four feet, or two pipes placed side-by-side at five feet in the ground in a two-foot wide trench. The Slinky™ method of looping pipe allows more pipe in a shorter trench, which cuts down on installation costs and makes horizontal installation possible in areas it would not be with conventional horizontal applications.

VERTICAL

Large commercial buildings and schools often use vertical systems because the land area required for horizontal loops would be prohibitive. Vertical loops are also used where the soil is too shallow for trenching, and they minimize the disturbance to existing landscaping. For a vertical system, holes (approximately four inches in diameter) are drilled about 20 feet apart and 100 to 400 feet deep. Into these holes go two pipes that are connected at the bottom with a U-bend to form a loop. The vertical loops are connected with horizontal pipe (i.e., manifold), placed in trenches, and connected to the heat pump in the building.

POND/LAKE

If the site has an adequate water body, this may be the lowest cost option. A supply line pipe is run underground from the building to the water and coiled into circles at least eight feet under the surface to prevent freezing. The coils should only be placed in a water source that meets minimum volume, depth, and quality criteria.

OPEN-LOOP SYSTEM

This type of system uses well or surface body water as the heat exchange fluid that circulates directly through the GHP system. Once it has circulated through the system, the water returns to the ground through the well, a recharge well, or surface discharge. This option is obviously practical only where there is an adequate supply of relatively clean water, and all local codes and regulations regarding groundwater discharge are met.

HYBRID SYSTEMS

Hybrid systems using several different geothermal resources, or a combination of a geothermal resource with outdoor air (i.e., a cooling tower), are another technology option. Hybrid approaches are particularly effective where cooling needs are significantly larger than heating needs. Where local geology permits, the “standing column well” is another option. In this variation of an open-loop system, one or more deep vertical wells is drilled. Water is drawn from the bottom of a standing column and returned to the top. During periods of peak heating and cooling, the system can bleed a portion of the return water rather than re-injecting it all, causing water inflow to the column from the surrounding aquifer. The bleed cycle cools the column during heat rejection, heats it during heat extraction, and reduces the required bore depth.

 

Get a Project Estimate From Our Trusted Professionals

Get an Estimate
Crowther's HVAC did a total install for an older house for me 14 years ago. They are very good at what they do and are also the epitome of customer service. Any problems that I have had they took care of immediately at very reasonable prices. Add in that they are all really good people and you have the formula for a very successful business. Rereccomend them highly."

Harry Haynie

I selected Crowther to replace both of my HVAC systems and they did a great job. They went the extra mile to correct duct work, and add a vent in order to bring my homes HVAC systems up to the best performance.

Blake Auchmoody

We had a total duel system heat pump replacement. It was a pleasure working with CHAC. From the sales rep to the technicians responsible for the install. Very professional in their craftsmanship and ensuring everything was installed and working correctly. Very courteous and respectful of our property. We are new to the area and am glad we chose CHAC for our HVAC needs.

Steve Casey

For 25 years, Crowther has provided excellent customer service and support for our Carrier zoned heat pump. They are responsive, helpful and great to work with! We love their seasonal maintenance program and have had them complete some system redesign for our home renovation. All around a great team!

Jill Bessler

Our Client

Reviews

For Our 24/7 EMERGENCY SERVICE Call Us Today!

Call Now: (800) 323-7478